6N135-500E

The 6N135-500E is designed for high-speed TTL/TTL applications. A standard 16-mA TTL sink through the input LED will provide enough output current for a TTL load and 5.6 kΩ pull-up resistor. These devices have a minimum CTR of 19% at IF = 16 mA.

Send Inquiry

Add To Inquiry

Description

Technical Parameters

The 6N135-500E optocoupler consists of an input side and an output side. The input side features a light-emitting diode (LED) that emits light when an electrical signal is applied to it. This emitted light is then detected by a phototransistor on the output side. The intensity of the light determines the phototransistor's conductivity, allowing it to either block or conduct current. This light-based signal transmission ensures that there is no direct electrical connection between the input and output sides, providing electrical isolation and preventing potential hazards associated with direct contact.

product-1268-913

Related Products:

Mfr Part	6N135	6N135-000E	6N135-020E	6N135-060E	6N135-300E	6N135-320E	6N135-360E	6N135-500E	6N135-520E	6N135-560E
Description	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT	OPTOCOUPLER, PHOTOTRANSISTOR OUT
Stock	80000	80000	80000	80000	80000	80000	80000	80000	80000	80000
Product Status	Active	Active	Active	Active	Active	Active	Active	Active	Active	Active
Number of Channels	1	1	1	1	1	1	1	1	1	1
Voltage - Isolation	3750Vrms	3750Vrms	3750Vrms	3750Vrms	3750Vrms	3750Vrms	3750Vrms	3750Vrms	3750Vrms	3750Vrms
Current Transfer Ratio (Min)	7% @ 16mA	7% @ 16mA	7% @ 16mA	7% @ 16mA	7% @ 16mA	7% @ 16mA	7% @ 16mA	7% @ 16mA	7% @ 16mA	7% @ 16mA
Current Transfer Ratio (Max)	50% @ 16mA	50% @ 16mA	50% @ 16mA	50% @ 16mA	50% @ 16mA	50% @ 16mA	50% @ 16mA	50% @ 16mA	50% @ 16mA	50% @ 16mA
Turn On / Turn Off Time (Typ)	200ns, 1.3us	200ns, 1.3us	200ns, 1.3us	200ns, 1.3us	200ns, 1.3us	200ns, 1.3us	200ns, 1.3us	200ns, 1.3us	200ns, 1.3us	200ns, 1.3us
Input Type	DC	DC	DC	DC	DC	DC	DC	DC	DC	DC
Output Type	1MB Transistor	1MB Transistor	1MB Transistor	1MB Transistor	1MB Transistor	1MB Transistor	1MB Transistor	1MB Transistor	1MB Transistor	1MB Transistor
Voltage - Output (Max)	20V	20V	20V	20V	20V	20V	20V	20V	20V	20V
Current - Output / Channel	8mA	8mA	8mA	8mA	8mA	8mA	8mA	8mA	8mA	8mA
Voltage - Forward (Vf) (Typ)	1.5V	1.5V	1.5V	1.5V	1.5V	1.5V	1.5V	1.5V	1.5V	1.5V
Current - DC Forward (If) (Max)	25 mA	25 mA	25 mA	25 mA	25 mA	25 mA	25 mA	25 mA	25 mA	25 mA
Operating Temperature	-55～C ~ 100～C	-55～C ~ 100～C	-55～C ~ 100～C	-55～C ~ 100～C	-55～C ~ 100～C	-55～C ~ 100～C	-55～C ~ 100～C	-55～C ~ 100～C	-55～C ~ 100～C	-55～C ~ 100～C
Package / Case	DIP8(7.62mm)	DIP8(7.62mm)	DIP8(7.62mm)	DIP8(7.62mm)	SMD8(7.62mm)	SMD8(7.62mm)	SMD8(7.62mm)	SMD8(7.62mm)	SMD8(7.62mm)	SMD8(7.62mm)
Package	Tube	Tube	Tube	Tube	Tape & Reel (TR)	Tape & Reel (TR)	Tape & Reel (TR)	Tape & Reel (TR)	Tape & Reel (TR)	Tape & Reel (TR)

Applications:

• High voltage insulation

• Video signal isolation

• Line receivers

• Feedback element in switched mode power supplies 

• High speed logic ground isolation – TTL/TTL, TTL/CMOS, TTL/LSTTL

• Replaces pulse transformers

• Replaces slow phototransistor isolators

• Analog signal ground isolation

Description:

These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance.

These single channel optocoup-lers are available in 8-pin DIP, SO-8, and Widebody package configurations.

The 6N135, HCPL-0500, and HCNW135 are for use in TTL/CMOS, TTL/LSTTL or wide-bandwidth analog applications. Current transfer ratio (CTR) for these devices is 7% minimum at IF = 16 mA.

The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are designed for high-speed TTL/TTL applications. A standard 16-mA TTL sink current through the input LED will provide enough output current for 1 TTL load and a 5.6 k pull-up resistor. CTR for these devices is 19% minimum at IF = 16 mA.

Hot Tags: 6n135-500e, China 6n135-500e manufacturers, suppliers, Optical Isolators, 6N136-500E, 4N35-500E, Photo Coupler Transistor, 6N135-500E, ACPL-217-500E

4N35-500E

6N136-500E

Send Inquiry